WEBVTT 00:00:00.020 --> 00:00:01.680 Music 00:00:17.179 --> 00:00:22.980 Speaker 1: Visit trb.fyi/disclaimers for a full disclaimer and liability notice. 00:00:24.460 --> 00:00:26.160 Speaker 1: When handling or working on 00:00:26.160 --> 00:00:28.340 Speaker 2: firearms, safety should always be first. 00:00:31.420 --> 00:00:35.800 Speaker 2: Visit trb.fyi for an article about the tools that we used in this video. 00:00:48.580 --> 00:00:55.320 Speaker 2: The Beretta Model 92 was designed in the early 1970s and was an evolution of the 1923 and 00:00:55.620 --> 00:00:56.640 Speaker 2: 1951 models. 00:00:57.860 --> 00:00:59.800 Speaker 2: The engine began in May of 1976. 00:01:09.180 --> 00:01:15.360 Speaker 1: Push the slide to the rear, and push up on the slide stop to hold the slide to the rear. 00:01:17.600 --> 00:01:24.800 Speaker 1: I use a zip tie to show that there's nothing in the chamber or the barrel, as well as the 00:01:24.660 --> 00:01:30.020 Speaker 1: magwell. This firearm is unloaded and safe to be handled. 00:01:38.100 --> 00:01:42.120 Speaker 1: To remove the slide from the frame, we're going to locate the disassembly button on 00:01:42.200 --> 00:01:49.380 Speaker 1: the right side of the frame and push it in. 00:01:52.140 --> 00:01:56.840 Speaker 1: Now we're going to locate the disassembly lever on the left side of the frame and rotate 00:01:56.950 --> 00:01:57.600 Speaker 1: it downwards. 00:02:00.180 --> 00:02:03.180 Speaker 1: Once it's in the full downward position, you can release the button. 00:02:04.820 --> 00:02:07.320 Speaker 1: Resist the temptation to press down on the slide lock. 00:02:07.930 --> 00:02:09.960 Speaker 1: Instead, push the slide back a little to release 00:02:09.960 --> 00:02:12.260 Speaker 2: it and now pull the slide off the frame. 00:02:29.400 --> 00:02:32.480 Speaker 2: Like most semi-automatic pistols, the 92 N96 00:02:32.480 --> 00:02:35.880 Speaker 1: recoil spring assembly rests on the front lug of the barrel. 00:02:37.220 --> 00:02:39.600 Speaker 1: Always use eye protection when working with springs. 00:02:41.500 --> 00:02:49.100 Speaker 1: We are going to slightly compress the recoil spring assembly while pulling it down and out of the slide slowly to relieve the tension on the spring. 00:03:04.180 --> 00:03:06.300 Speaker 2: Now pull the recoil spring from the guide rod. 00:03:21.440 --> 00:03:25.780 Speaker 2: To remove the barrel, we're going to push the locking block plunger while pushing the 00:03:25.900 --> 00:03:27.360 Speaker 2: barrel assembly forward slightly. 00:03:28.660 --> 00:03:30.700 Speaker 2: Then we can remove the barrel from the bottom of the slide. 00:03:43.239 --> 00:03:46.340 Speaker 2: For this step we are going to need the barrel and slide assemblies. 00:03:48.180 --> 00:03:52.460 Speaker 2: Insert the muzzle of the barrel assembly into the top opening of the slide and push up on 00:03:52.540 --> 00:03:54.460 Speaker 2: the rear to finish installing the barrel. 00:04:06.920 --> 00:04:09.740 Speaker 2: For this step we're going to need the recoil spring and guide rod. 00:04:12.200 --> 00:04:14.340 Speaker 2: Simply insert the spring onto the guide rod. 00:04:27.260 --> 00:04:32.040 Speaker 2: For this step we are going to need our recoil spring assembly and the slide assembly with 00:04:32.040 --> 00:04:32.880 Speaker 2: the barrel installed. 00:04:35.630 --> 00:04:39.480 Speaker 2: We are going to insert the end of the recoil spring assembly into the bottom hole of the 00:04:39.480 --> 00:04:44.320 Speaker 2: slide and compress it so that the back of the guide rod will seat into the locking block 00:04:44.600 --> 00:04:44.800 Speaker 2: cutaway. 00:05:06.980 --> 00:05:10.960 Speaker 2: The back of the guide rod is held into the locking block cutaway by spring tension. 00:05:19.540 --> 00:05:20.020 Speaker 2: For the final 00:05:20.020 --> 00:05:24.760 Speaker 1: step of reassembly, you're going to need your completed slide assembly and your frame. 00:05:28.200 --> 00:05:32.160 Speaker 1: Align the slide onto the frame guide rails and push it to the rear as far as you can. 00:05:36.240 --> 00:05:38.720 Speaker 1: Then push up on the slide lock to capture the slide. 00:05:40.180 --> 00:05:45.220 Speaker 1: Now rotate the disassembly latch rearward and release the slide so that it comes home. 00:05:47.150 --> 00:05:48.780 Speaker 1: Your firearm is now reassembled. 00:05:53.180 --> 00:05:58.260 Speaker 1: If you find our videos helpful, consider supporting us for free by using our affiliate links and 00:05:58.320 --> 00:06:01.140 Speaker 1: banners on our site or by donating to us on Patreon. 00:06:03.640 --> 00:06:07.040 Speaker 1: Please remember to subscribe to our channel, it helps us more than you realize. 00:06:09.760 --> 00:06:10.540 Speaker 1: Thank you.