WEBVTT 00:00:02.439 --> 00:00:03.280 Music 00:00:17.780 --> 00:00:23.240 Speaker 1: Visit trb.fyi/disclaimers for a full disclaimer and liability notice. 00:00:24.600 --> 00:00:26.180 Speaker 1: When handling or working 00:00:26.180 --> 00:00:28.560 Speaker 2: on firearms, safety should always be first. 00:00:32.500 --> 00:00:39.640 Speaker 2: Visit trb.fyi for the full article of tools that we used in the 92, 96 and M9 video series. 00:00:51.980 --> 00:00:56.120 Speaker 2: Using a screwdriver, remove the grip screws and lock washers. 00:01:37.620 --> 00:01:42.000 Speaker 2: Use a finger to push up on the back of the grips to get them above the grip screw bushings. 00:01:51.840 --> 00:01:54.020 Speaker 2: Repeat the process on the other side of the frame. 00:02:06.280 --> 00:02:09.259 Speaker 2: The disassembly latch is located on the left side of the frame. 00:02:10.509 --> 00:02:15.380 Speaker 2: We will need to rotate the disassembly latch upwards by first pushing in on the disassembly 00:02:15.540 --> 00:02:16.000 Speaker 2: latch button. 00:02:25.760 --> 00:02:29.360 Speaker 2: and then rotating the disassembly latch until it contacts the slide rail. 00:02:36.880 --> 00:02:41.780 Speaker 2: Slowly release the spring tension on the disassembly latch button and then remove it from the frame 00:02:41.850 --> 00:02:42.640 Speaker 2: by pulling it out. 00:02:53.580 --> 00:02:55.840 Speaker 2: Now remove the disassembly spring from the slide. 00:03:04.160 --> 00:03:06.360 Speaker 2: The disassembly latch can now be pulled from the frame. 00:03:32.400 --> 00:03:34.520 Speaker 2: The trigger bar is located on the right side of the frame. 00:03:36.800 --> 00:03:41.120 Speaker 2: Using a pair of needle nose pliers, carefully remove the trigger bar spring from the trigger 00:03:41.320 --> 00:03:42.120 Speaker 2: bar and the frame. 00:03:43.280 --> 00:03:46.660 Speaker 2: Gently lift up to remove the trigger bar spring from the hole in the receiver. 00:03:56.080 --> 00:04:00.840 Speaker 2: To remove the trigger bar, push up on the trigger bar from the rear and pull from the frame. 00:04:30.620 --> 00:04:35.180 Speaker 2: The slide stop is located on the left side of the frame and its spring sticks through 00:04:35.180 --> 00:04:37.640 Speaker 2: a hole in the frame to retain the trigger pivot pin. 00:04:39.440 --> 00:04:41.380 Speaker 2: Slowly pull the slide stop from the frame. 00:04:58.660 --> 00:05:01.440 Speaker 2: and pull up on the spring to remove it from the hole in the frame. 00:05:34.960 --> 00:05:37.520 Speaker 2: The trigger is held into the frame by the trigger pivot pin. 00:05:38.600 --> 00:05:39.960 Speaker 2: This pin holds the trigger to the 00:05:39.960 --> 00:05:42.480 Speaker 1: frame as well as retains the trigger spring. 00:05:44.640 --> 00:05:47.300 Speaker 1: To remove this pin we will push from the right to the left. 00:05:48.880 --> 00:05:51.140 Speaker 1: The left side of the pin has a larger flat head. 00:05:52.800 --> 00:05:58.380 Speaker 1: Using a 3/32 inch punch push the pin from the right to the left until it clears the frame. 00:06:03.040 --> 00:06:07.380 Speaker 2: Once this punch is all the way into the frame do not remove it until you are ready as this 00:06:07.320 --> 00:06:08.780 Speaker 2: This is holding in the trigger spring. 00:06:18.919 --> 00:06:22.500 Speaker 2: Place a finger over top of the spring and then remove the punch. 00:06:23.060 --> 00:06:24.940 Speaker 2: This keeps the spring from flying out of the frame. 00:06:26.660 --> 00:06:29.040 Speaker 2: Now rotate the frame and the spring will fall free. 00:06:40.320 --> 00:06:44.220 Speaker 2: Now the trigger can be removed by pushing up and removing it through the top of the frame. 00:07:08.040 --> 00:07:12.300 Speaker 2: The mainspring and hammer strut guide are held in place by a pin located at the bottom 00:07:12.360 --> 00:07:12.840 Speaker 2: of the frame. 00:07:13.920 --> 00:07:18.340 Speaker 2: The mainspring puts a lot of tension on the hammer strut guide and we must be careful when 00:07:18.420 --> 00:07:19.000 Speaker 2: removing it. 00:07:20.200 --> 00:07:24.100 Speaker 2: Using a 3/32 inch punch, drive this pin out of the frame. 00:07:37.860 --> 00:07:41.160 Speaker 2: Place a finger into the frame and your thumb on the hammer strut guide. 00:07:41.760 --> 00:07:44.100 Speaker 2: Push up with your thumb and remove your punch. 00:07:45.000 --> 00:07:46.660 Speaker 2: Carefully release the spring tension. 00:07:55.260 --> 00:07:56.820 Speaker 2: Now remove your hammer strut guide. 00:08:02.680 --> 00:08:03.820 Speaker 2: Tip your frame up and shake. 00:08:04.560 --> 00:08:05.700 Speaker 2: Your mainspring will come out. 00:08:23.180 --> 00:08:25.020 Speaker 2: The hammer is held in place by the hammer pin. 00:08:31.640 --> 00:08:35.900 Speaker 2: Using a 3/16 inch punch, push the hammer pin in from the right side. 00:08:41.780 --> 00:08:43.320 Speaker 2: Now pull your hammer away from the frame. 00:08:51.200 --> 00:08:53.940 Speaker 2: Turn your frame upside down and the hammer strut will fall from the frame. 00:09:13.700 --> 00:09:18.720 Speaker 2: The sear and the sear spring are located at the back of the magwell and held in place by 00:09:18.740 --> 00:09:19.360 Speaker 2: the sear pin. 00:09:20.320 --> 00:09:24.360 Speaker 2: The sear spring is under tension and we'll need to put a finger over it when we're removing 00:09:24.470 --> 00:09:26.620 Speaker 2: our punch so that we can maintain control. 00:09:29.480 --> 00:09:33.120 Speaker 2: Using a 1/16 inch punch, drive the pin through the frame. 00:09:44.440 --> 00:09:47.140 Speaker 2: Place a finger over the sear spring and remove your punch. 00:09:57.060 --> 00:10:00.340 Speaker 2: Now rotate your frame and your sear and sear spring will fall free. 00:10:23.700 --> 00:10:27.560 Speaker 2: The hammer release and firing pin block lever are held in place by a pin. 00:10:29.060 --> 00:10:33.780 Speaker 2: There are two pins in this area. There's a roll pin to the back and a straight pin to the front. 00:10:34.420 --> 00:10:36.520 Speaker 1: In this step we'll be working with the front pin. 00:10:38.080 --> 00:10:42.800 Speaker 1: Using a 1/16 inch punch drive out the pin from the right side of the frame to the left. 00:10:46.860 --> 00:10:50.700 Speaker 1: Remove your punch and then pull out the firing pin block lever from the front. 00:10:55.600 --> 00:10:56.020 Speaker 1: If you tip 00:10:56.020 --> 00:10:58.820 Speaker 2: your frame, the hammer release lever will fall free. 00:11:07.040 --> 00:11:10.360 Speaker 2: To remove the ejector, we'll need to remove the ejector spring pin. 00:11:11.640 --> 00:11:18.580 Speaker 2: Using a 1/16 inch roll pin punch, drive out the ejector spring pin from the right side of the frame to the left. 00:11:43.060 --> 00:11:44.700 Speaker 2: Now pull the ejector free from the frame. 00:12:02.320 --> 00:12:06.500 Speaker 2: The magazine catch is located where the trigger guard meets the front strap and is reversible 00:12:06.730 --> 00:12:07.780 Speaker 2: for left handed shooters. 00:12:14.700 --> 00:12:19.740 Speaker 2: To remove the magazine catch, push in into the rear with the fingertip on the opposite 00:12:20.040 --> 00:12:21.760 Speaker 2: side of the magazine release button. 00:12:22.800 --> 00:12:27.680 Speaker 2: Go slowly when removing this from the frame so that you don't lose the spring or the bushings. 00:12:45.140 --> 00:12:49.520 Speaker 2: Slowly pull up on the spring to release it and the bushings from the magazine catch. 00:13:19.700 --> 00:13:22.880 Speaker 2: Consider supporting us on Patreon, or use our affiliate links 00:13:22.880 --> 00:13:24.000 Speaker 1: on our webpage to help 00:13:24.000 --> 00:13:25.520 Speaker 1: us produce more quality content. 00:13:28.740 --> 00:13:32.600 Speaker 1: Please remember to subscribe to our channel, it helps us more than you realize.